![Graziano Sag 14 Manual Graziano Sag 14 Manual](http://nerdgenerous.weebly.com/uploads/1/2/3/9/123992832/713122325.jpg)
I have been watching eBay for Graziano accessories for several years and have never seen anything for these lathes. You asked about buying accessories such as steady and follow rests on eBay. Otherwise, you will have coolant/cutting oil all over your wall, ceiling, floor and yourself.
GRAZIANO SAG 14 MANUAL INSTALL
If you plan to use a coolant system, I would highly recommend constructing a back splash shield and install a chuck guard. I also find them a bit cumbersome to set up. I have used the carriage stops on occasion but they don't seem to be really precise enough to trust them for consistent machining to a shoulder. Thanks PetePete, I have my SAG 14 backed up to a wall and I haven't had any issues cleaning out the chip pan from the front.
GRAZIANO SAG 14 MANUAL FULL
It's a hobby thing right now, so I don't t anticipate mountains of chips in the near term I have the full set of carriage stops, how often do you guys use them? Are they usable for shoulder stops and threading stops? They seem incredibly handy. Questions: I plan to the have it back up against a wall, but notice the chip pan come off on the back side, I can make a hoe like device for chip removal, will that be sufficient or should I try and spin the lathe around? I guess I'll get to try out my left hand drill bits. I also investigated the front way covers which I think have been gone for quite awhile, the holes were all packed with crap and a few of the bolts are snapped off. I tried to get picture's of all these things. The 3 jaw chuck is a Buck 230mm or 9+ inches and appears to be truable I'm not sure who makes the 4 jaw it is 10' and has plenty of dings but seems to operate just fine. I haven't done much cleaning yet, there are some dings on the ways and leading edge of the compound and the chuckling the lathe has been well used, but everything seems solid.
![Graziano Sag 14 Manual Graziano Sag 14 Manual](https://www.picclickimg.com/00/s/MTYwMFgxMjAw/z/2qUAAOSwXYtYydWL/$/GRAZIANO-Sag-180-Manual-Engine-Lathe-8-Chuck-_1.jpg)
I have a tool post, and a few holders coming, and most importantly a gas line being trenched in, so I'll have heat. I now have the lathe powered up, via the VFD. Don ClementThanks Don, I have one on the way. I plan to the have it back up against a wall, but notice the chip pan come off on the back side, I can make a hoe like device for chip removal, will that be sufficient or should I try and spin the lathe around? It's a hobby thing right now, so I don't t anticipate mountains of chips in the near term I have the full set of carriage stops, how often do you guys use them? Are they usable for shoulder stops and threading stops? They seem incredibly handy.Ī goldenrod piston pump works well with Vactra #2 on my Sag 12. Questions: Do I need a special type of oiler for the little button type oil ports on the lathe, I'm looking at Goldenrod piston pump oil can will that do it? Are tool posts for 10-18 inch swing the most appropriate? For tooling 1 inch holders? I see an auction coming with a lot of 1' and 1 1/4' tool holders on offer.Īnyone have a favorite dial setup for the cross feed? It came with a DRO for the Z axis so I'm good there. I have a 10 HP VFD to power it, and I believe I have sorted out the oils I need to keeps it going. It's going in the garage, I'm an IT guy that likes to play with machines, in my spare time. I'd love to get a steady rest for it too, are such things ever on eBay? I see a local 7.5 HP rotary phase converter, which I think so be more than I need, but any advice is welcome.
![Graziano Sag 14 Manual Graziano Sag 14 Manual](https://i0.wp.com/occasionmachines.com/wp-content/uploads/2017/05/torno_graziano_sag14-2.jpg)
It comes with 3 and 4 jaw chucks, both 10' which need cleaning up, and that's about it. I hope to get a 5c nose or collect adaptor for it.
GRAZIANO SAG 14 MANUAL PDF
Hello, My first real machine will be coming home in a week or so, would anyone have a scanned or PDF manual for a 50s ish SAG 14? I very excited about the lathe and have checked out it's history etc on lathes.UK.